Lectrsonics IFBR1A-VHF
Bookmark and Share

Lectrsonics IFBR1A-VHF


Multi-Frequency Belt-Pack IFB Receiver - VHF

BSW PART: IFBR1A-VHF

Lectrsonics IFBR1A-VHF
Lectrsonics IFBR1A-VHFLectrsonics IFBR1A-VHF
Wireless IFB (interruptible fold back) systems are used for talent cueing and crew communications in broadcast and motion picture production. In other cases, the IFB system is used by directors and other management to monitor program audio during a production. The IFBR1a-VHF receiver provides simplicity and flexibility in a package that is intuitive for untrained users to operate.

The default frequency of the receiver is set by two rotary switches on the side panel. Up to five additional frequencies can also be programmed into the receiver memory using the scan mode. If more than one frequency is stored in the receiver, the operator can scroll through all stored frequencies by simply pressing the volume knob. Basic operation is simply a matter of rotating the knob to turn power on and adjusting the volume level. Additional frequencies are added by holding the knob in until the LED begins blinking and the receiver begins to scan. The receiver will search for signals that contain a pilot tone and automatically stop scanning and wait for the operator to either store that frequency or continue scanning. A special button push sequence is required to set the receiver into the scanning mode to prevent accidental changes to the receiver memory. Simplified instructions are laser engraved into the housing of the receiver. The scanning process is performed at two different sensitivity levels. The first scan is performed at a reduced sensitivity to avoid falsely locking onto IM (intermodulation) signals rather than true carriers. This reduced sensitivity scan is necessary when the unit is programmed in close proximity to the transmitter. If no signals are found in the first scan, a single button push will set the receiver to full sensitivity and begin a second scan. Full sensitivity scanning is necessary to program the receiver at a distance away from the transmitter.

The design uses +/-20 kHz FM deviation for efficient use of the bandwidth, with compandor noise reduction circuitry for an excellent signal to noise ratio. A supersonic Pilot Tone signal controls the audio output squelch to keep the receiver silent when no transmitter signal is received. The receiver operates on a single 9 volt alkaline or lithium battery. Alkaline battery life is up to 8 hours. Lithium battery life is well over 20 hours. The LED indicator changes color from green, to yellow, to red as the battery voltage declines to provide plenty of warning before operation ceases.

An internal relay in the receiver will automatically detect a monaural plug connected to the output jack and switch accordingly. Full output power is available with either type of connector, without the power losses that result from a resistive circuit design. The antenna input is provided by the shield of the cable and headset or earphone connected to the output jack.

The receiver will drive a wide variety of earbuds, headphones and induction neck loops at substantial levels, with loads from 16 Ohms to 600 Ohms. The receiver is housed in a rugged machined aluminum package. A protective leather pouch with an integrated belt clip is included.

Main Features:
• Preset (default) frequency is manually set with hex switches
• Scan mode stores up to five additional frequencies in memory
• Multi-color LED and rotary control for programming and operation
• High sensitivity for extended operating range indoors or outdoors
• Rugged machined aluminum housing
• Attached battery door
• 8 hours battery life (alkaline)
• 20 hours battery life (lithium)
• Protective leather pouch is included

Specifications:
• Operating Frequencies (MHz): 174.100 to 215.750 MHz
• Available Frequencies: 239
• Channel Spacing: 175 kHz
• Frequency control: Crystal Controlled Phase Locked Loop
• Sensitivity: 1 uv (20 dB SINAD)
• Signal/Noise ratio: 95 dB A-weighted
• Squelch quieting: 90 dB
• AM rejection: 50 dB, 10 uv to 100 mv
• Modulation acceptance: ±20 kHz
• Spurious rejection: Greater than 70 dB
• Third order intercept: 0 dBm
• Frequency response: 100 Hz to 10 kHz, (±1db)
• Pilot tone: 29.997 kHz, 4.5 kHz deviation (fixed crystal controlled)
• Audio output, headphone: 1 Vrms into 50 ohms minimum
• Antenna: Headphone cable
• Programmable memory: 5 frequencies
 • Front panel controls: Single knob controls Audio Output Level, Power on, programming and Scan Frequency Selection
• Indicators: 1 tricolor LED Indicator for power on, blinks to indicate channel number, blinks fast during scan, and turns yellow or red for low battery.
• Power requirement: Single 9V Alkaline Battery for approximately 8 hours operation.
• Power consumption: 60 ma.
• Allen wrench for knob: 0.035” (Lectro part number: 35854)
• Weight: 7.3 oz with battery
• Size: 3.6 x 2.4 x 0.8 inches

List Price: $895.00
$629.00
Free Shipping!
Usually Ships in 1-2 Weeks - Contact BSW for more Details
You Saved:
$266.00 (30%)


View ALL Lectrosonics Products

Customers also Viewed...
Recently Viewed