Belar AMMA2
Bookmark and Share

Belar AMMA2


*AM Modulation Monitor And Analyzer "The Wizard"

BSW PART: AMMA2

Belar  AMMA2
The AMMA-2 is a DSP-based microprocessor-controlled, digital AM modulation monitor/analyzer that precisely measures positive and negative peak modulation, peaks per minute, average peak modulation, modulation density, and more. In addition to monitoring standard AM modulation, the AMMA-2 accurately monitors modulation-dependent carrier level (MDCL) AM transmissions. During MDCL broadcasts, the RF carrier level becomes a dynamic component of the AM signal.

The AMMA-2 tracks the carrier, capturing the highest and lowest values of the carrier level, as well as the decibel ratio of the carrier high/low. Modulation readings are referenced to the carrier level appropriate for the MDCL system in use. The optional remote meter panel displays positive modulation, negative modulation, and carrier level simultaneously on three large analog meters.

The AMMA-2 features user-defined parameters and settings for maximum flexibility. Two large UP/DOWN menu keys are used to cycle the 16-character alphanumeric display to the desired menu; the UP/DOWN parameter keys are then used to select the desired setting. The unit configuration may be saved to the on-board non-volatile memory so the settings are retained in the event of a power loss. A noise menu selection displays rms-detected SNR in decibels (flat or de-emphasized) on the front panel. A carrier cutoff indicator consisting of three front panel LEDs continuously monitors the approach of negative modulation to carrier cutoff. A unique "Normal Modulation" indicator shows when modulation is falling within user-defined parameters. A built-in Audio Sentry audio failure alarm alerts you to loss of modulation or drops in modulation level. An RS-232/RS-422 port allows the AMMA-2 to be accessed via personal computer.

The ASCII command set, documented in the users manual, provides an easy way for users to write their own command and control software. Alternately, the AMMA-2 will be supported in the future by The Wizard Software, which provides unit control and graphing and logging capability for all the AMMA-2 measurements. A remote alarm connector consisting of 8 pairs of relay contacts provides alarm status information for hard-wired applications. NRSC de-emphasis may be selected internally by moving a jumper plug.

Measurements:
• Positive Peak Modulation in Percent
• Negative Peak Modulation in Percent
• Positive Peaks-per-Minute Count
• Negative Peaks-per-Minute Count
• Positive Peak Average & Peak Min Modulation
• Negative Peak Average & Peak Min Modulation
• Positive Average/Peak Modulation Ratio
• Negative Average/Peak Modulation Ratio
• Normal Modulation Peaks-per-Minute Count
• AM Noise rms detected in dB
• Carrier Level
• Carrier Reference
• Carrier High in sliding 1 minute window
• Carrier Low in sliding 1 minute window 
• Carrier Ratio High/Low in dB

Settable Parameters:
• Positive & Negative Peak Modulation Indicator
• Positive & Negative Peaks/Minute Indicator
• Normal Modulation Indicator
• Positive & Negative Peaks/Minute Duration
• Audio Failure Alarm - Time & Modulation
• Modulation Mode (Normal/Fixed/MDCL/IMOD)
• MDCL Reference • Carrier Shift Alarm
• Carrier Failure Alarm - Time & Level
• Display Hold Time vTime Mode (Real/Past)
• Infinite Hold
• Audio Outputs (Test/Meter)
• Modulation Calibrator
• Tuning Frequency
• Tuning Mode (Dir/Auto/Scan/Lock)
• Tuning Frequency Increments

Specifications:
• RF Frequency Range: 250 kHz to 30 MHz
• RF Tuning Increments: 1 kHz
• RF Sensitivity: 1 to 10 volts rms
• RF Input Impedance: 500 ohm or 50 ohm, internally connected
• Accuracy: 1.0%
• Display Large: Large 3 digit LED for Negative Modulation, 16-character alphanumeric LED display for menus and parameters
• Frequency Response : ±0.1 dB, 30 Hz to 10.2 kHz -3dB @ 11.9kHz -100 dB @ 16 kHz
• Audio Outputs
• Audio Monitor : +10 dBm, 600 ohm, balanced (XLR), NRSC or Flat
• Audio Test: 2.5 V rms unbalanced (BNC)
• Frequency Response : ±0.1 dB, 30 Hz to 10.2 kHz
• Distortion : less than or equal to 0.1% @ 99% modulation
• IMD (SMPTE, CCIF, DIM): less than or equal to 0.1% @ 99% modulation
• Signal to noise ratio: 75 dB
• Signal Delay: Test: 3 ms., Meter: 90 ms. Automatic Carrier Level Adjustment range : 25-150%
• Remote Meter Output : Jack for optional MP-17 analog remote meter panel
• Remote Alarms: Relays for Loss of Modulation Normal, Negative PPM, Positive PPM Loss of Carrier, Remote, and General alarms. Relays can be set NO or NC
• Serial Interface: RS-232/RS-422
• Unit Interface : Wizard Standard Interface
• Power Requirements: 20 watts, 100-240 Vac 50/60 Hz
• Dimensions: 1 3/4"H x 14"D x 19"W (EIA rack mount)
• Shipping Weight : 10 lbs (4.5 kg)

List Price: $3,495.00
$3,177.27
Free Shipping!
Usually Available in 1-2 Weeks
You Saved:
$317.73 (9%)


View ALL Belar Products

Customers also Viewed...
Recently Viewed