­

Ashly NX1502

Ashly

BSW PART:
NX1502

Power Amplifier 2 x 150 Watts at 2 Ohms

$1,329.00 $1,661.00
You save $332.00
$1,329.00 $1,661.00
You save $332.00

Free Shipping

Out of stock

Add to quote
Qualifies for free shipping
  • Main Features:
  • Selectable 80Hz 2nd-order Hi-pass filter, limiter, and input gain per channel
  • Remote DC level control per channel
  • Extensive protection circuitry, continuously variable cooling fan
  • Euroblock input connectors
  • Euroblock loudspeaker connectors
  • Detachable AC mains line-cord connector
  • Safety/Compliance: cTUVus (pending), CE, FCC, RoHS
  • Specifications:
  • Voltage Gain: Selectable at 26dB, 32dB, 38dB, or 1.4V
  • Damping Factor: >250 (8 Ohm load <1kHz)
  • Input High Pass Filter: 80Hz 2nd order
  • Distortion (SMPTE, typical): <0.5%
  • Distortion (THD-N, typical): <0.5% (8 Ohms, 10dB below rated power, 20Hz–20kHz)
  • Channel Separation: -75dB (dB from full output, 1kHz)
  • Signal-to-Noise (unweighted) 20Hz-20kHz, Gain@26dB:
  • >99dB (all 150x models)
  • >96dB (all 75x models)
  • Frequency Response: 20Hz-20kHz, +/-0.05dB
  • Balanced Input Connector: Euroblock 3.5mm
  • Input Impedance: 10k Ohms
  • Maximum Input Level: +21dBu
  • Speaker Output Connector: Euroblock 7.62mm
  • Remote DC Level Control: Euroblock 3.5mm – Gnd, CV, V+ per input
  • Attenuators (per channel): Rear panel, Fully off = Mute
  • Amplifier Protection: Shorted output power limiting, over-temperature, DC-output, power-supply fault, mains-fuses & inrush-current limiting
  • Cooling: Continuously variable temperature controlled fan
  • Environmental: 32°F-120°F, (0°C-49°C) non-condensing
  • Weights and Dimensions:
  • Unit Dimensions: 19”W x 1.75”H x 14.54”D (483mm x 45mm x 369mm)
  • Shipping Dimensions: 25.2"W x 2.5"H x 19.5"D (641mm x 64mm x 495mm)
  • Unit Weight: 1504/754 12.1lbs (5.5kg), 1502/752 11.3lbs (5.1kg)
  • Shipping Weight: 1504/754 16.0lbs (15.0kg), 1502/752 14.2lbs (6.4kg)
  • Front Panel LED Indicators:
  • POWER (white): Switch: On, Off, Standby (flashing)
  • PROTECT (red): On (fault condition or shut down), Off
  • SLEEP (blue): On, amplifier is asleep from audio inactivity
  • DISABLE (yellow): On, power switch & attenuators are disabled Per Channel
  • CLIP/MUTE (red): Clip @ 1dB below rated output / Mute
  • SIGNAL (green): -18dB below rated output
  • CURRENT (green): Brightness is proportional to output current
  • TEMP (yellow): On dim at 90% max operating temperature, On full bright + protect at 100%
  • BRIDGE (green): Per Channel Pair, On, Off
  • Remote Accessories:
  • WR-1: 2-Channel Level Control
  • Power Requirements (50 – 60Hz):
  • Nominal Voltage Input: 100 – 240VAC
  • Operating Range: 70 – 270VAC
  • Minimum power-up: 70VAC
  • Power Supply Type: SMPS with active PFC (Power Factor Correction)
  • AC Mains Line Cord Connector: Detachable Nema 5-15 for USA (May vary for export)